6 Tips for Water Damage Repair

Repairing Water Damage

There is no doubt that water can cause a lot of damage to your home. There could be cracks in your foundation, which is caused by seeping and leaking water. Corrosion, rust, and mold can also spread when there are leaks in your home. Water damage repair. can be stressful too, and often you would not be sure of what to do during the repairs. Not to mention it can also be costly to fix any of the damages that have been caused by water inside of your home. But there is a solution to all of your issues with water damages.

Water Damage

Prevention

That one simple solution is prevention; you can stop water damage from happening in the first place by following these tips.

  • Fix Leaking Pipes

One of the primary sources of water damage in your home can be water leaking pipes. Turn of the water source at the meter to stop the flow of water. Then fix leaking pipes

  • Pump out water

Another way to clear the waters is to pump them out. A sump pump is a device that you can submerge underwater, and it pumps out all the water from your basement using a pipe or hose. It is particularly useful if you have got a flooded basement. Professionals often use these pumps to remove the water.

  • Open the window

If the weather isn’t too humid outside, moving air outside naturally can remove the moisture in the air of your home. Opening the windows and doors can start the circulation of air around the area. Open all drawers and cabinets to dry them out too.

  • Use a fan

High-powered fans can also help with the water damage repair Austin. These fans can be bought and even rented for as long as you need them. The sizes of these fans also vary according to the size of your area. When used they can effectively suck out any excess moisture in the air.

  • Dehumidifiers

A way to remove the moisture from the air is to use a dehumidifier. There are different kinds of dehumidifiers, but a simple portable dehumidifier can easily take all the water vapor from the air and clear out small and contained areas like your bathroom or bedroom. When you start to dehumidify, shut all the doors, and windows. This is to avoid any moisture or vapor from seeping into your area.

  • Use Desiccants

Desiccants like clay and silica gel can quickly absorb the moisture wherever they used. Sealing these materials in airtight containers and putting them in contained areas can help reduce the moisture there. However, This can take a long time, though, depending on how much moisture there is. Knowing these tips for correcting water damage can quickly help you overcome the high cost and difficulties in dealing with all the damage in your home. It is a good idea to learn all the ways to prevent water damage and also know what to do when dealing with its consequences.

 

Replacing Broken Glass in a Steel Casement Window

Requires Specialized Tools and Processes

Replacing a broken pane of glass on a steel casement window isn’t like repairing wood sash. It takes different tools, special materials, and a fine-tuned process. But once the former are assembled, the job is easy enough for anyone with a little DIY experience and a willing attitude.

Step 1: Assemble your materials, starting with the glass. Unless your glass is ordinary 1⁄8″ double-strength sheet glass, purchase 3⁄16″ or 1⁄4″ plate glass at a glass supplier to match the existing. (The new pane of glass should be about 1⁄8″ narrower than the opening’s height and width.) Steel sash should be glazed with putty specifically made for metal windows, such as DAP 1012. (Wood window putty won’t last.) You’ll also need an awl and hammer, metal sash clips, duct tape, a wire brush, needle-nose pliers, a small window suction cup, and whiting.

Step 2: Wearing eye protection and a respirator and using basic lead-safe work practices, begin removing the old putty. Because old putty can be hard and may contain lead, Portland cement, or asbestos powder, use an awl and hammer, not heat, to loosen it. Look for areas where the putty is loose or missing, insert the awl point between the putty and steel, and gently tap the awl with your hammer; the force needed will depend on the condition of the putty and its composition. If the putty is intact, start from the middle.

 Step 3: Once the putty is removed and the edges of the glass are exposed, look for two metal spring clips on each vertical side of the opening; pull them out with the needle-nose pliers. These clips are fragile and easy to lose; if you can hold onto them and they remain intact, you can reuse them. Otherwise, purchase new ones at a glass company. Next, with the ground and floor protected to catch glass shards, old putty, and dust, cover both sides of the glass with wide masking or duct tape to contain breakage. If the pane isn’t badly cracked, pull it out using a small window suction cup, or by tapping gently from the inside out. With the glass out, finish removing the old putty. If the sash rebate is rusty, use a wire brush or a drill and wire brush attachment to remove as much rust as possible. Brush or vacuum the dust away, and prime the cleaned area with a coat of oil-based rusty-metal primer.

Step 4: Since DAP 1012 is usually oily on top of the can and dense at the bottom, remove all of the material and knead it into a pliable ball, using whiting if necessary to firm it to an appropriate consistency. (If the putty is dry on the top of the can, return it for fresh material.) The new pane of glass can’t touch the metal frame in any direction, so back-bed a thin layer of putty in the frame to seat the glass, protect it from thermal movement, and create a weather seal. Install the back-bed with your fingers or a putty knife, pushing the putty into the frame (warm putty is more pliable). Next, insert the pane of glass, and gently push it into the putty until it is well-seated. Using needle-nose pliers, install the metal sash clips on each side to secure the pane.

Step 5: Before glazing, remove excess back-bedding material from the interior side with your putty knife. Next, glaze the exterior—I like to push the putty into the frame and glass tightly with the putty knife, but the common method of rolling putty into a snake and then inserting it also works. Take care to respect the interior sight lines of the sash—putty and paint on the outside shouldn’t be visible from the inside. Tool the putty, pushing it tightly to the frame and glass while cutting the edge away at the sight line. To finish, sprinkle a little whiting or plaster dust on a clean cotton rag, and carefully wipe away all the smears. After the putty dries, paint with two coats of oil-based paint.